| Fish Tank Clan :: Forums :: Fish Tank Side Forums :: Philosophy |
|
« Previous topic | Next topic » |
| Steps to make a Flickering Light By LED | ||
| Author | Post | ||
|
|||
Registered Member #1518
Joined: Thu Jan 01 1970, 12:00AMPosts: 9 |
LEDs (light giving off diodes) have changed incandescent lights for creating effects in theater and stage play productions. You are able to build a digital circuit that can make an LED flicker to ensure that you can use it to produce the consequence of flame inside a fire place. A couple of parts from an electronics supply shop and knowledge about a soldering iron is needed, out of the box adult supervision, when the person making the electronic circuit is underage.|GU10 1×3w Aluminium 1 Place newspaper lower on the work surface. Straighten the 2 conductive hooks at the base from the red-colored LED with needle nose pliers. 2 Cut two 6-inch bits of electric wire with wire blades. With wire strippers, remove one half inch of insulation, measured having a ruler, from each one of the finishes of these two wires. 3 Solder the finish of among the wires to among the two contacts around the resistor. Allow the solder awesome for any minute. 4 Solder another contact around the resistor straight to the short pin around the red-colored LED. Allow the solder awesome. 5 Solder one finish from the other wire towards the lengthy pin around the red-colored LED. Allow the solder awesome. 6 Wrap electrical tape round the hooks from the red-colored LED and also the contacts around the resistor.|GU10 3x1W Aluminium 7 Solder the free finish from the wire attached to the resistor towards the contact labeled "positive input" around the DCx16 circuit board. Allow the solder awesome for any minute. 8 Solder the free finish from the wire attached to the red-colored LED towards the contact labeled "negative input" around the DCx16 circuit board. Allow the solder awesome. 9 Solder the black wire from the 3 major-volt battery holder towards the positive contact around the DCx16 circuit board. Allow the solder awesome. 10 Solder the red-colored wire from the 3 major-volt battery holder towards the negative contact around the DCx16 circuit board. Allow the solder awesome.|E27 1*3W LED Spot Light 11 Place two AA batteries in to the 3-volt battery holder. Watch the red-colored LED illuminate and flicker off and on. |
||
| Back to top |
|
||
| amishburrito |
|
||
amishburrito
Registered Member #1185
Joined: Fri Oct 30 2009, 09:53AMPosts: 352 |
I'd be happy to make this if you send me the materials for free +s&h no cods Edited Tue Nov 15 2011, 12:38PM | ||
| Back to top |
|
||
|
|||
|
Registered Member #2727
Joined: Thu Jan 01 1970, 12:00AM Posts: 159 |
Thousand and A single Nights Ladies Gucci 'GTimeless' Diamond Dial Bracelet Check out Breitling For Bentley Collection the Flying B line mens SWISS REPLICA ROLEX Replica ROLEX Replica BREITLING Replica TAG HEUER Replica CARTIER Replica OMEGA Replica IWC watches Replica PATEK PHILIPPE Replica A LANGE&SOHNE Replica ALAIN SILBERSTEIN Replica ARMANI Replica AUDEMARS PIGUET Replica BAUME&MERCIER Replica BELL&ROSS Replica BVLGARI Replica CHOPARD Replica CONCORD Replica CORUM Replica FERRARI Replica GRAHAM Replica HERMES Replica HUBLOT Replica JAEGERLECOULTRE Replica LONGINES Replica Panerai Replica PIAGET Replica RADO Replica UBOAT Replica ZENITH ROMAIN JEROME ULYSSE NARDIN VACHERON&CONSTANTIN Zachary David Alexander "Zac" Efron (born Oct eighteen, prom dresses gowns prom dresses gowns cheap party dresses cheap party dresses dresses for mother of the bride dresses for mother of the bride 1987) is short prom dress short prom dress unusual wedding gifts pakistani brides dresses pakistani brides dresses cheap bridesmaid dress cheap bridesmaid dress cheap wedding dress cheap wedding dress cheap bridesmaid dresses cheap bridesmaid dresses | ||
| Back to top |
|
||
Powered by e107 Forum System
|
|